SHF Dragon Ball Son Gohan Ssj2 Event Exclusive EE 龍珠 孫悟飯 超2 超級撒亞人2 會場特別版
price: 580=540+40 hkd
this post is about the ssj2 son gohan which coming from the event exclusive version father and son kamehameha pack
this repaint version also carries the issue from the original one
the wrists on this figure cannot be swivelled (honrizontal spun) becoz the connection is super tight
that cannot be fixed by adding some silicone oil or vaseline
here are some steps to fix that
1. use hot water to add heat for detaching the front arms
2. use hobby knife to make 2 small pits on both sides as image
3. use hand drill to dril 2 holes for each pit
4. near the wrist is the first and center is the second
5. try to connect the holes as grooved
once the grooves are ready, the wrist joints are then free and they can be swivelled (honrizontal spun) now
thx for reading🤝🏻
這個是關於父子龜波氣功會場特別版中的超2, 超級撒亞人2, 孫悟飯
這次改色再版同樣保留之前原裝的問題
手腕是不能水平旋轉
單靠遙控車雪油或凡士林是沒有用
因為內在構造太過緊
以下是一些步驟去解決這個問題
1. 先用熱水加熱去拆除前臂軟膠
2. 用筆刀在內骨輕劃出兩條刻線, 用作對位
3. 用手鑽在刻線上鑽兩個窿
4. 第一個在近手腕關節位置, 第二個在中間
5. 打通兩個窿令它們變成一條槽
當兩條槽都完成後, 手腕關節就可以水平旋轉
多謝閱覽🤝🏻
=========================================
price: 580=540+40 hkd
this post is about the ssj2 son gohan which coming from the event exclusive version father and son kamehameha pack
this repaint version also carries the issue from the original one
the wrists on this figure cannot be swivelled (honrizontal spun) becoz the connection is super tight
that cannot be fixed by adding some silicone oil or vaseline
here are some steps to fix that
1. use hot water to add heat for detaching the front arms
2. use hobby knife to make 2 small pits on both sides as image
3. use hand drill to dril 2 holes for each pit
4. near the wrist is the first and center is the second
5. try to connect the holes as grooved
once the grooves are ready, the wrist joints are then free and they can be swivelled (honrizontal spun) now
thx for reading🤝🏻
這個是關於父子龜波氣功會場特別版中的超2, 超級撒亞人2, 孫悟飯
這次改色再版同樣保留之前原裝的問題
手腕是不能水平旋轉
單靠遙控車雪油或凡士林是沒有用
因為內在構造太過緊
以下是一些步驟去解決這個問題
1. 先用熱水加熱去拆除前臂軟膠
2. 用筆刀在內骨輕劃出兩條刻線, 用作對位
3. 用手鑽在刻線上鑽兩個窿
4. 第一個在近手腕關節位置, 第二個在中間
5. 打通兩個窿令它們變成一條槽
當兩條槽都完成後, 手腕關節就可以水平旋轉
多謝閱覽🤝🏻
=========================================
