SHF Dragon Ball Gohan Training Ver Hair Piece Custom 龍珠 孫悟飯 訓練服 頭髮 改造
shf doesnt release the training ver gohan
even though i tried to custom one
but there is no hair piece and face plate fitting in with training ver
the best ver in the market should be the great saiyaman ver
however the great saiyaman cannot change face, just one expression
finally, i cut the hair piece and molded to fit the shf sroe faces
here are the steps
1. use the hot water to heat up the hair piece for 5mins
2. the front part and the basenoe can be detached by using hands and model knife
3. there are two pegs installed from front part to base at both left and right, they are glued so i used the model knife to cut the pegs
base hair
4. use the hand drill to drill the holes at left and right sides that the broken pegs location of base hair
5. cut away some part at the center to fit the sroe faces
front part
6. use the model knife to separate the face and bangs (i forgot to take the pic of the face🤦🏻♂️)
7. dig the front bangs to make the hair next to ears at left and right thinner
8. drill the holes on both base and front bangs to install the pegs, i use the toothpick and they around 6-7mm each
9. check and refine the not good areas by using uv glue (putty or other materials can be also used)
completed👏🏻👏🏻👏🏻
thx for ur reading🤝🏻
shf 沒有生產訓練服的孫悟飯
盡管我自行改造了一個
但發現沒有合適的頭髮及面形
而市面上比較理想的是撒亞超人的頭雕
但那個不能換面🤦🏻♂️
經過一段時間的內心交戰
我改造那個頭雕為可以換上地球悟空面形
以下是步驟
1. 先用熱水浸那顆頭雕大約5分鐘
2. 前part及後髮可以用手及筆刀分離
3. 前part在左右兩邊各有榫被膠水黐死了, 我用筆刀直接切斷它們
後髮
4. 用手鑽在斷榫的位置鑽窿
5. 在中間位置用筆刀切走部份塑膠, 留位給地球悟空面形
前part
6. 用筆刀切開前髮及面形 (我忘了給分開了的面形拍照)
7. 挖一下前髮令到左右兩邊的水薄一點
8. 左前髮及後髮鑽窿, 用來上榫, 我暫時用了牙簽作榫, 大約6-7mm長
9. 檢查及用uv膠水作修補 (也可以用上其他物料如混合畢地)
完成👏🏻👏🏻👏🏻
多謝閱覽🤝🏻
=========================================
=========================================
https://www.facebook.com/siukamadbuyrecord/posts/3488525347918805
=========================================
shf doesnt release the training ver gohan
even though i tried to custom one
but there is no hair piece and face plate fitting in with training ver
the best ver in the market should be the great saiyaman ver
however the great saiyaman cannot change face, just one expression
finally, i cut the hair piece and molded to fit the shf sroe faces
here are the steps
1. use the hot water to heat up the hair piece for 5mins
2. the front part and the basenoe can be detached by using hands and model knife
3. there are two pegs installed from front part to base at both left and right, they are glued so i used the model knife to cut the pegs
base hair
4. use the hand drill to drill the holes at left and right sides that the broken pegs location of base hair
5. cut away some part at the center to fit the sroe faces
front part
6. use the model knife to separate the face and bangs (i forgot to take the pic of the face🤦🏻♂️)
7. dig the front bangs to make the hair next to ears at left and right thinner
8. drill the holes on both base and front bangs to install the pegs, i use the toothpick and they around 6-7mm each
9. check and refine the not good areas by using uv glue (putty or other materials can be also used)
completed👏🏻👏🏻👏🏻
thx for ur reading🤝🏻
shf 沒有生產訓練服的孫悟飯
盡管我自行改造了一個
但發現沒有合適的頭髮及面形
而市面上比較理想的是撒亞超人的頭雕
但那個不能換面🤦🏻♂️
經過一段時間的內心交戰
我改造那個頭雕為可以換上地球悟空面形
以下是步驟
1. 先用熱水浸那顆頭雕大約5分鐘
2. 前part及後髮可以用手及筆刀分離
3. 前part在左右兩邊各有榫被膠水黐死了, 我用筆刀直接切斷它們
後髮
4. 用手鑽在斷榫的位置鑽窿
5. 在中間位置用筆刀切走部份塑膠, 留位給地球悟空面形
前part
6. 用筆刀切開前髮及面形 (我忘了給分開了的面形拍照)
7. 挖一下前髮令到左右兩邊的水薄一點
8. 左前髮及後髮鑽窿, 用來上榫, 我暫時用了牙簽作榫, 大約6-7mm長
9. 檢查及用uv膠水作修補 (也可以用上其他物料如混合畢地)
完成👏🏻👏🏻👏🏻
多謝閱覽🤝🏻
=========================================
=========================================
https://www.facebook.com/siukamadbuyrecord/posts/3488525347918805
=========================================